Shakagore Use paired wire of 22 to 18 gage sufficient in length between the source device and the SST amplifier. Use quality wire, and if runs are more than 3 meters use at least 12 gage wire. In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance. Persistent Thermal shutdown indicates steps need to be taken to increase airflow across the channel or channels heat sink. Installation see rack mounting section if applicable Ventilation. Should the breaker trip, lower or remove the amplifier input signals.
|Published (Last):||13 August 2019|
|PDF File Size:||13.13 Mb|
|ePub File Size:||15.32 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mur Input Sensitivity Gain Switch. When the power supplies have stabilized the channel will come out of mute and the LED will change to green normal operation. Gold plated locking banana plugs are available from Bryston.
Bryston can provide an optional fan package if required. Any amplifier that is constantly operated into clipping indicates a more powerful amplifier is needed for that application.
Bryston C Series 4B SST Dimensional Drawing Before inserting a banana plug into the binding post be sure to tighten the post nut to avoid rattling and to provide full insertion of the banana plug. In amnual never use longer cables than necessary, never coil excess cable length, and keep signal wires away from AC power or speaker cables.
Each SST channel gives the user the option of switching between either balanced input or single ended input. Use paired wire of 22 to 18 gage sufficient in length between the source device and the SST amplifier. Ship the amplifier only in the original packing material, as the unit is not insurable by carriers otherwise. Bryston will custom build cables for your application. This is the home theatre brysto for single ended or un-balanced operation. Graph shows that distortion is essentially unaffected by load.
Cables should be dressed away from input and power cables. Banana plugs offer a quick disconnect option. Bridged W 8 ohms Max. This warranty is considered void if the defect, malfunction or failure of the product or any component part was caused by damage not resulting from a defect or malfunction or abuse while in the possession of the customer.
In the unlikely event you have a problem and must return it for service you must use the proper packing material. Unrestricted air-flow across its heat sinks is a must. Balanced input Vs Single ended input: When the channel has cooled to a safe operating condition the channel will return to normal operation.
Should your instillation conditions be constricted, then additional forced air-cooling may be necessary. Each amnual selects a gain of ssr 1v or 23dB 2v. All SST amplifiers are convection cooled. Clipping flashing red Clipping occurs when the channel output level no longer can follow the level increase at the input Overdriven input condition.
If both channel LED indicators are unlit the amplifier probably needs only to byrston powered on. Combinations may be used when bi-wiring. Heat Dissipation 8 ohms — Bridged W 8 ohms Max. The SST amplifier uses a magnetic-trip circuit breaker 1 to protect the amplifier. Each channel selects a balanced or single ended input. The RED binding post is connected to the amplifier output. Note that copper wire is malleable and may require further tightening after the initial installation.
Different input configurations result in slightly bbryston noise readings. Check that the voltage rating on the label conforms with your locality. On the rear panel is provided a high current plug for the power cord receptacle.
Installation see rack mounting section if applicable Ventilation. In the event of a defect or malfunction, Nryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file manyal Bryston. This is the home theatre setting for balanced operation Or use this setting with any systems where the volume control rotation is limited to the bottom half of the control or less.
Never lift the safety ground to the amplifier nor remove the ground pin from the plug. Use quality wire, and if runs are more than 3 meters use at least 12 gage wire. This will ensure the amplifier msnual protected in future transport. The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source.
Bryston 4B SST User Manual
Sakree Should your instillation conditions be constricted, then additional forced air-cooling may be necessary. Any SST channels thermally shutting down during operation indicates insufficient air flow, and a remedy must be found for cooling the amplifier. Installation see rack mounting section if applicable Ventilation. The 1v setting provides the most amplifier gain — 29 dB.
BRYSTON 4B SST MANUAL PDF